On July 14th, 2023, I purchased a 2017 GL1832 Audio comfort-ABS-Navi Pearl White with only 13,864 miles! The previous owner could not locate his records for GW service but claims to have kept the service current.
I will have the Extended warranty carry over with this GW purchase for approximately 2 years. *I will need to address some "streaks" in the Navigation screen, and after reviewing many comments concerning the Navigation screen issue, Honda Warranty will cover such observed issues with my Navigation screen.
Maintenance completed today, July 24th, 2023.
2017 GL1832 HPNM Maintenance
VIN: JH2SC68N2HK300021 MODEL: GL18 HPNM
**Honda Protection Plan Contract #FM2017000002300
Length of Coverage: 96 months/8 years
Date Issued: 12/28/2017.
Contract Expiration Date: 12/28/2025
Contract Expiration Mileage: Unlimited
Deductible: $0.00
Battery Charger AC: Duracell aka Batteries Plus
Model: Ultra 12v-6v-AGM-Lithium 12.3v capable charger
July 14th, 2023, I purchased 2017 GL1800 HPNM Audio comfort-ABS-Navi-Pearl White with only 13,864 miles! The previous owner says he could not locate his records for GW service but claims to have kept the service current.
I will have the Extended warranty carried over with this GW purchase for approximately two years.
{NOTE: *I will need to address some "streaks"} in the {Navigation screen} after reviewing many comments on “GoldWing1800Riders Forums” concerning the Navigation screen issue, and that the “ Honda Warranty” will cover such observed issue with my Navigation screen.
Maintenance was completed today, July 24th, 2023.
(1) Brake Maintenance consisting of the installation of;
(2) Speed Bleeders completed;
(3) new brake pads front and rear, brake flush as I observed brake fluid in the rear brake reservoir was a dark amber color upon inspection; subsequently, I removed the remaining brake fluid in the rear brake reservoir, cleaned the minute residue observed in the bottom of the reservoir and flushed and bleed the braking system, this included the Anti-dive valve and Clutch Fluids. Completed!
NOTE: After removing the current front and rear brake pads, it was noted that there was barely any noticeable wear compared to the new pads; I reinstalled them. The recent order of (**New Front & Rear brake pads will be installed once the current brake pads need replacement!)
(4) R/R Front Tire: Bridgestone Exedra 130/70R/18-63H G709 & Rear Tire: Bridgestone Exedra G704 Radial 180/60-16 74H Rear Tire or may go with the Avon Cobra Rear tire; I estimate I could get another thousand or two miles from the current tires if I am gentle with the braking & throttle; Update: I had the existing *** The Bridgestone front tire was replaced with the Avon Cobra Chrome front tire, removed and replaced by Cycle Gear in Pinellas Park-FL after removing them from the GW. The newly purchased Bridgestone Exedras replaced them (5) earlier. (6) Rear Drive service R/R with “Pro Honda Drive Shaft Oil 80w-90 # 08208-14000” **scheduled maintenance was completed on August 2nd, 2023. Drained approximately 2 oz. from the rear drive oil; replaced with 4 oz “Pro Honda Drive Shaft Oil 80w-90.
NOTE: Oil/Filter R&R-oil was very dark; I feel much better knowing the "White Pearl" has fresh oil & filter! The next change is due at 19,900 for 6K miles or 21,000 @ 8K on current oil, as Honda recommends an oil/filter change every 8,000 miles; I'm not comfortable going till 8 thousand miles for my WP, aka White Pearl! I added 12 ounces to the coolant reservoir as it was lower than it should normally be * I will also keep an inspection of the reservoir level to make sure there are no leaks in the cooling system. I will R&R the coolant fluids in the winter.
Will be performing a (2) Brake job consisting of the installation of (3) Speed Bleeders; (4) new brake pads front and rear, and brake flush as observed brake fluid was dark amber color upon inspection; this will include the Anti-dive valve; (5) R/R Front Bridgestone Exedra 130/70R/18-63 H G709 & Rear Bridgestone Exedra 180/60R/R16 80H or may go with the Avon Cobra tires; I estimate I could get another thousand or two current tires if I am gentle with the braking & throttle; (6) Rear Drive service R/R with Pro Honda drive shaft oil!
All the above have been completed as of January 5th, 2024!
(1) I will do a nice wash and wax with clay bar treatment and a wipe on Ceramic coating as well. Completed! Ongoing.
(2) Dress the Rims and Tires. Done-Ongoing. Completed August 1st, 2023!
(3)
ELECTRONICS-ACCESSORIES:
(1) Electrical Connect Bluetooth device (already purchased). Installed!
(2) EC Ground Loop Isolator (purchased, not used, as I had no interference- will sell item).
(3) Evaluate previous owners' LED lighting and either keep or trash. Will keep them!
(4) Add additional accessories, such as electronics, black/chrome, etc.
(5) Re-evaluate the Kurry driver & passenger pegs. Trash or keep? Keep-save some $$$$
(6) CB-Radio & Antenna? I will not purchase CB with more current technology for communication far & above CB Radio technology.
(7) Ram mounts reassessments for mounting for iPhone-GPS if I need additional besides the GW Navi unit-TBD/To Be Determined. ***Purchased the Carpuride W502 installed, and it works great. It mirrors the iPhone Carplay and works really great! (Update: I purchased the Carpuride 702pro seven-inch screen to replace the 502 five-inch screen. The 502 will serve as reserve if the 702pro fails or sell the Carpuride 502.)
I may be adding another Satellite Emergency device unless I use the Spot that I canceled service on, as I was not doing any long-distance traveling. I may sell it for an updated model before my Route 66 Adventure later in 2024, provided my health maintains me. Planning the Route is already formatted GPS on the Desktop with "MyRoutes GPS Mapping." I will update you in the near future! (I did not make the RTE 66 this year as I had hoped, so hopefully, the late spring of 2025 will work out for that adventure.)
ELECTRONICS-ACCESSORIES aka Farkles:
Merchant details: shop.muthco.com
August 2nd, 2023, previously ordered & then installed the “MUTH MIRRORS” Blue tint with Amber Chevron turn indicators. They do bring extra safety for drivers to the rear, knowing my intentions when turning in front of them. I may go back to adjust the wiring, as the Kurry “Y” splitter and the MUTH wiring made for a tight fit in the small compartment below the front cowl area beyond the mirrors. **MUTH MIRRORS carry a *three-year or 36,000-mile warranty against defects of the “LEDs”! Effective until July 27th, 2026!
November 30th, 2023
I installed the Show Chrome “Tridium DRL-Fog-Turn Signals.” I did have an electrical connection issue on the Fog lights due to defective (BLUE Connectors at the Fog lights connecting points). I learned that it is a defective issue, as noted by some reviews from previous customers. Initially, I tried using wiring tape to hold the two connection points together to complete the circuit (Failed!)
I have attempted to get a response from Wingstuff customer service concerning having failed components replaced [wire lead from turn signals to Fog-running lights & defective Fog-DLR Light Switch. I have not received any response from Wingstuff after two emails on their website. I also mailed a letter via USPS. I will post on the Wingstuff website on
GL1800RIDERS about this dilemma of no response from Wingstuff!
***I found a solution by using small zip ties to hold the two male/female connections together to complete the circuit. I then sealed it with wiring tape. It was after several tests of the operation of the Fog lights that I secured the wiring leading down from the “Turn Signals” connections and ran the Fog lights leads down in the front fairing cowl to the Fog lights located in the lower cowl. Before closing up everything, I again checked the operation of the Fog-DRL-Turn signals, and all worked!
*** I installed the power provided by the PDM60 Isolator in the left front pocket (Show Chrome-USB Dual Charger 2.5v X2 charging ports)!
*** I installed another Dual USB Charger/Battery Voltage monitor into the rear Tour Trunk powered via the PDM60 Isolator.
*** The next installation will be the Show Chrome “Left side Accessory USB Power Switch.” (It's installed and working!)
ADD any additional accessories below:
(9) MADSTAD Windshield purchased October 23rd, 2023
Toni or Blair 0830-1630 for pick up & payment for a 14” MADSTAD windshield.
On October 27th, 2023, I installed the 14” MADSTAD, which was too high in height at the lowest position. I called and spoke with Blair and explained the issue, and he said they would exchange it, which is not a problem.
November 1st, 2023, I drove back to MADSTAD to return the 14” shield for the 12” that had already been made for me. Upon comparing the new shield and placing it next to the 14”, the new shield was actually another 14” shield! Blair apologized for the error. He said he would get the 12” sent to me the following day, November 2, 2023, via UPS. I received the UPS tracking number, and the new 12” shield was delivered to me on November 3rd, 2023! It was the correct size! The fit was spot on, and I’m looking forward to seeing if all the hype is true about MADSTAD!
(10) I installed the 12” MADSTAD on November 4th, 2023, without incident, and I can now easily see above the windshield!
I will take it out and note the various angles to provide my comfort zone on the Highway at speed. To be continued
**Test rides on local roads and adjustments: I have not had any long rides at higher speeds for any length of time (all urban roads). But right now, from 30mph up to 60-70 mph, I have just smooth airflow in the rider and no buffeting of the helmet! Happy so far. The position of the air wings also changes the various airflows, which help regulate or fine-tune the airflow on and around the rider.
(11) On November 5, 2023, the Carpuride W502 Apple Car Play was ordered and is awaiting delivery for installation: Carpuride W502 Wireless Portable Dual Bluetooth Waterproof IP67 Motorcycle Stereo. This will enable Apple Car Play functions on the 2017 GL1832 via headphones or the onboard Electrical connection Bluetooth to allow feedback through the bike speakers! (An Update and review will follow installation.) (See 11 & 15 below for additional information.)
(12) 11/5/2023 I purchased Carpuride W502 via their website. This unit allows you to have CarPlay on the 2017 GL1832 while your phone is stored away from the elements! (This allows the iPhone CarPlay to be mirrored onto the Carpuride screen! Great! Apple CarPlay is now on the 2017 GL1832! Sweet! (I will update and review it after receiving and installing it on the GL1832.) R/R with the Carpuride 702pro 7” screen.
(13) The UTOPIA Backrest was ordered and installed from November 14 to 2023, and I’m looking forward to having lower midback support! I had one on the 2012 GL1832 and loved it! (I will update the review once I have some miles with Utopia!) LOVE IT!!!
(14) Honda 2012-2017 Service Manual with Electronic Trouble Shooting Manual Attached.
Delivered: via FedEx on August 6, 2023
**See (12) above Screen Shots of the Carlinkit Dongle: below pages.
(15) Apple Car Play Carpuride W502 installed 11/21/2023. I wired the W503 into the left cubby compartment area with an open existing hot (+) lead via wiretap and grounded (-) on the same lead. The W503 has an in-line 3amp fuse, so I did not need to run wiring down to the battery or to the PDM60 Isolator.
A Bluetooth connection was established with the iPhone, and I customized the ACP=Apple Car Playlist to my preferences. The GPS did not coordinate with the active iPhone Google Maps or Apple maps relating to E-W-S-N. I will update once I can do an actual test ride to see if the coordination of the location mode of travel displays the same as the iPhone mapping source. (I am still trying to figure out if I can tie the W503 into the GW speakers, yet it appears it is designed to connect via BT to the Helmet (according to the instruction material enclosed), which I have not attempted to test yet.
I will update you soon once I get the trial ride of the W503. The purchase was to keep the iPhone out of the weather, particularly the summer sun, which causes heat-related issues by reducing the screen brightness and, at times, disabling the iPhone to protect itself from heat damage.
I now have the option of storing the iPhone on my person, the left front cubby unsecured, the center lockable storage compartment, and the rear Tour Trunk, which I wired with a 3.5 & 2.5 USB charger/voltmeter, which was installed on 11/21/2023. (It is wired into the " PDM60 Power Distribution Module. ") **I can get Audio via the GW speakers once I BT the Carpuride W502 to the Electrical Connection! Good News!
Update**11-28-2023 I tried out the built-in EQ “Rock Mode,” and it sounds way better than the 2018 GW! Hearing the sound from the 2017 GW knocked my socks off! Love this CarpuRide W502!!! SEE BELOW for the purchase of the Carpuride 702pro installed to replace the W502.
(16) November 25, 2023: I installed the Show Chrome Tridium DRL-Fog-Turn Signal kit. The installation was lengthy, about 7 hours, taking my time and requiring me to readapt the disassembly of the plastic for some 5 years since I did on my 2012 GL1832. The Cruise Man DIY video was a great reference. Another issue was fishing the wire leads from the “Turn Signals on R & L” down within tight crevices from the mirrors down to the area of the FOG light connections. ☹!
I took all the front cowling off the front, the windshield, and its components to find an easier access point. I used the 3’ zip tie on the respective R & L mirrors to fish the Fog Lights cables and connect to both Fog lights! 😉
The connections (Blue) were not making the clasp lock as they should. I finally got the R side to lock, but the L never did (I will tape the Blue Connectors @ the Fog lights so they don’t disconnect!) I reconnected the (-) on the battery to test the connections and functions of the fog lights. All was working as they should (DRL-Amber Turn signals R & L)-Retina fryers Fog lights! I used the “Jumper” so the Fog lights will remain “ON” even when the “Bright lights function is active on the GW.” I will complete getting everything buttoned up tomorrow!
Problem with the Tridium fog light installation see the following;
Thanks for the reply! I am about to have my Tridium Fog-DRL-Turn signal kit finished up. It appears Show Chrome has already installed the "resistors" on the latest version of their Tridium Fog light kits. As new to me, 2017 GW has all incandescent lamps. I am not experiencing any issues with all functions of the Fog lights LEDs and the incandescent lamps. Yippy!
What was a pain in the Kester was intermittent LEDs working when they desired. I had to go back & forth to figure out the problem.
It turns out that the connectors from the main wiring from the mirrors down to the fog lights were the problem. The connectors on each of the plugs in the fog light were defective. I could never get the male & female clips to lock onto each other. It appears that they were just a smidge too long to allow a flush fit of the opposing connections.
Initially, I tried taping them with wiring tape in hopes it was enough to hold them together, but that didn't work! So, I decided to trim a small amount of the end of each connector so that it would allow a secure contact and allow the lock to secure the connection. That did the trick or so I thought but being that the plastic lock on the tab was so thin and flimsy, it was easy to separate them, the result was lights that worked when they wanted to!
**Update January 6, 2024: the main fog lights will not stay on; the only way they would activate is if I pressed very firmly on the Fog Light switch! The running and turn signal lights worked properly. I ordered a replacement “Fog Light Switch” from SoCal in hopes this will correct the issue with the crappy Show Chrome fog light switch! I will update once I R/R the Show Chrome fog light switch. Paying the kind of money for the Show Chrome lights “Tridium” and having to replace a Switch is a bummer! I will contact Show Chrome and ask for a replacement switch. If they want me to send the defective one, I will have it available because I will already have R/R the Show Chrome with the SoCal switch! Update to follow!
My Fix
So, I used a zip tie to wrap around the vertical axis of both the right and left connectors to hold them together. This appears to have solved the issue. I sure don't want to deal with a loose connection issue and disassemble it to deal with this again! If I have a reoccurring issue, I will cut the wires and soldier them together.
If I hear anyone having this issue on the forum with the Tridium fog lights with intermittent LED, I pass my fix on to them. I have a sneaking suspicion I will not be the only one who purchased the Black Friday sale on the Tridiums that got the bad batch of connectors on the fog light connecting points. I have way too many hours wasted getting the Fog lights operational, running down the issue, and fixing it. Oh well, I am happy with the outcome,, and these are some great Fog-DRL-Turn signals once I got them working correctly! Buttoned the GW up & no issues with the fog lights! 11-28-2023
[[UPDATE]] I installed the Socal Fog-DRL switch.
January 10th, 2024, I installed the Socal Fog Light switch to replace the Show Chrome Fog-DLR switch. It was defective as you had to press and hold the switch down for the DLR to activate; otherwise, the DLR would cut off when you released the switch. The Socal switch worked, but I had to use a wire tie to keep the connector between the switch and the power lead from the left cubby pocket wiring. At this moment, the Fog-DRL is working normally! 😊
**Show the Chrome 12v USB accessory for the left cubby pocket-storage area. It is currently being shipped, and I will update you after installation.
Update RE: Show Chrome 12v USB Accessory Charger 11-28-2023 was delivered. After looking over the packaging, I noticed that these were for the 2018 and up GWs. But they will fit into the 2017 Cuddy left side without issue. I drilled the 1-1/4” hole that was factory molded for the cutout to accept 12v accessory.
I installed the charger but have not wired it into the electrical system yet. I will have to route the power leads to the PDM60 later. I tied up the buttoning of the GW backup after the installation of the Tridium fog lights!
(17) Knob Key Project Order Number: 925807081-LOWES Clwtr
I ordered 2-Key Blanks “Axxess 27R B Cassettes +” Lowes 11-28-2023. I will make two Knob keys for Fuel Door & Glove Box.
I also ordered 2- Knobs of Black Rubber “Honda 35601-MCA-A8”1 from Parts-Zilla for making the Knob-Keys. (Update on completion of the installation)
In-Store Pick-Up Lowes Clearwater Store.
The above keys were cut down for the Honda Black radio knobs, and a small slot was cut off from each knob so the keys could be inserted and glued! I used the JB Weld plastic epoxy. It worked very well and provided a solid medium for attaching the keys to the radio knobs, which will be used on the Fuel access door and the Center cubby. This will allow me not to have to remove the ignition key to open the fuel and center cuddy when I need to have access to them. When leaving the GW, I can remove the two Radio knobs and secure them in the center cubby or the rear tour trunk.
HONDA CUSTOMER SERVICE AKA “MAW HONDA”
If YOUR problem still has not been resolved to YOUR satisfaction, please write Motorcycle Customer Service Department, American Honda Motor Co., Inc., P.O. Box 2200, Torrance, CA 90509-2200, or YOU may call Motorcycle Customer Service at (866) 784-1870.
(18) Honda Rear Spoiler OEM Pearl White installed October 13th, 2024, purchased from Cycle Max. The following additional accessories were installed with the rear Spoiler:
The new “Carpuride 702pro” was mounted in the center of the Madstad mounting base shield and secured with security mounting bolts and security Ram-type mounts requiring a Security Key to remove/reinstall them. The large real estate of the screen was a nice improvement for these old eyes! Once I figured out how to use Bluetooth and sync the iPhone, it worked flawlessly. Once I turn the key on, it initiates start-up, and “Apple Car Play” is up and running. I have hundreds of songs stored with various Genres of Artists at my fingertips on the “Apple Music App”.
(20) November 28th – 30th, 2024, Upgraded the OEM H3 Lo Beam Headlight Bulbs to “Pathfinder SoCal” LEDs." I purchased SoCal from the Pathfinder-SoCal web store. The installation was rated a (3) out of (5) scale of difficulty due to the tight areas which you must work on the front interior fairing area on the left & right sides of the fairing.
I was so impressed with the bright white image the LEDs provided compared to the OEM H3 Halogen bulbs' (brown/yellow) appearance. In fact, I liked them so much that I decided to purchase a second set of SoCal LEDs to replace the OEM Hi-Beam H3 Halogen with LEDs! These were purchased from Moto Tour (Pinellas Park-FL) as Pathfinder SoCal did not have any available. The installation is rated a (5) of (5) of difficulty.
This was due to the removal of the pockets Right and left, and the upper high beam mounting locations were very tight and cramped in the upward recesses of the fairing above the Lo beams! The ballast was secured in the small open areas on the right and left pockets of the interior fairing plastics.
*Despite the difficulty of this installation, it was again well worth the safety of nice crisp white bright headlights of Hi & Lo beams! The low points of this installation of the Hi beam LEDs, as noted, (1) were removing the top right and left shelter pockets, (2) the foot warmer controller adjuster component, the Plastic around the ignition key, and dislodging the left plastic panel of the inner fairing to gain access from the front section of the wheel area, rearranging the electrical wiring within those spaces.
It’s no wonder “Pathfinder SoCal” recommends that a professional technician install the Hi-Beam LEDs. But if you are mechanically inclined and have patience, you can handle this installation. Ask me how I know. 😊
(21) Gold Strike Cup Holder (rider) see bulleted additional accessories added:
I will have the Extended warranty carry over with this GW purchase for approximately 2 years. *I will need to address some "streaks" in the Navigation screen, and after reviewing many comments concerning the Navigation screen issue, Honda Warranty will cover such observed issues with my Navigation screen.
Maintenance completed today, July 24th, 2023.
2017 GL1832 HPNM Maintenance
VIN: JH2SC68N2HK300021 MODEL: GL18 HPNM
**Honda Protection Plan Contract #FM2017000002300
Length of Coverage: 96 months/8 years
Date Issued: 12/28/2017.
Contract Expiration Date: 12/28/2025
Contract Expiration Mileage: Unlimited
Deductible: $0.00
Battery Charger AC: Duracell aka Batteries Plus
Model: Ultra 12v-6v-AGM-Lithium 12.3v capable charger
July 14th, 2023, I purchased 2017 GL1800 HPNM Audio comfort-ABS-Navi-Pearl White with only 13,864 miles! The previous owner says he could not locate his records for GW service but claims to have kept the service current.
I will have the Extended warranty carried over with this GW purchase for approximately two years.
{NOTE: *I will need to address some "streaks"} in the {Navigation screen} after reviewing many comments on “GoldWing1800Riders Forums” concerning the Navigation screen issue, and that the “ Honda Warranty” will cover such observed issue with my Navigation screen.
Maintenance was completed today, July 24th, 2023.
- **The Oil/Filter R&R Oil was very dark in color; I feel much better knowing the "White Pearl" has fresh oil and filter! The next change due: 19,926 is based on 6k miles instead of the 8,000k that Honda recommends for intervals of the Oil/Filter change every 8,000 miles; I’m uncomfortable going 8,000 miles for my WP, aka White Pearl!
- I added 12 ounces to the coolant reservoir as it was lower than it should have been. I will also inspect the reservoir level to ensure no leaks are in the cooling system. I will R&R coolant fluids in the winter. Inspection of the Antifreeze was a nice medium tint green color in the radiator's filler neck. Coolant Change Service completed as dated above! 11-29-2024 I checked the coolant level while adding the LEDs Hi & Lo Beams, and it appeared fresh as when I did the R/R it on first Maintenance @ purchasing the GW.
(1) Brake Maintenance consisting of the installation of;
(2) Speed Bleeders completed;
(3) new brake pads front and rear, brake flush as I observed brake fluid in the rear brake reservoir was a dark amber color upon inspection; subsequently, I removed the remaining brake fluid in the rear brake reservoir, cleaned the minute residue observed in the bottom of the reservoir and flushed and bleed the braking system, this included the Anti-dive valve and Clutch Fluids. Completed!
NOTE: After removing the current front and rear brake pads, it was noted that there was barely any noticeable wear compared to the new pads; I reinstalled them. The recent order of (**New Front & Rear brake pads will be installed once the current brake pads need replacement!)
(4) R/R Front Tire: Bridgestone Exedra 130/70R/18-63H G709 & Rear Tire: Bridgestone Exedra G704 Radial 180/60-16 74H Rear Tire or may go with the
NOTE: Oil/Filter R&R-oil was very dark; I feel much better knowing the "White Pearl" has fresh oil & filter! The next change is due at 19,900 for 6K miles or 21,000 @ 8K on current oil, as Honda recommends an oil/filter change every 8,000 miles; I'm not comfortable going till 8 thousand miles for my WP, aka White Pearl! I added 12 ounces to the coolant reservoir as it was lower than it should normally be * I will also keep an inspection of the reservoir level to make sure there are no leaks in the cooling system. I will R&R the coolant fluids in the winter.
Will be performing a (2) Brake job consisting of the installation of (3) Speed Bleeders; (4) new brake pads front and rear, and brake flush as observed brake fluid was dark amber color upon inspection; this will include the Anti-dive valve; (5) R/R Front Bridgestone Exedra 130/70R/18-63 H G709 & Rear Bridgestone Exedra 180/60R/R16 80H or may go with the Avon Cobra tires; I estimate I could get another thousand or two current tires if I am gentle with the braking & throttle; (6) Rear Drive service R/R with Pro Honda drive shaft oil!
All the above have been completed as of January 5th, 2024!
- OIL CHANGE includes Oil Filter due@ 19,900 6k-miles or 21,000 @ 8k
- Inspect front & rear brakes R&R if needed
- Inspect brake reservoir levels and brake fluid (Dot 3); all is completed OK!
(1) I will do a nice wash and wax with clay bar treatment and a wipe on Ceramic coating as well. Completed! Ongoing.
(2) Dress the Rims and Tires. Done-Ongoing. Completed August 1st, 2023!
(3)
ELECTRONICS-ACCESSORIES:
(1) Electrical Connect Bluetooth device (already purchased). Installed!
(2) EC Ground Loop Isolator (purchased, not used, as I had no interference- will sell item).
(3) Evaluate previous owners' LED lighting and either keep or trash. Will keep them!
(4) Add additional accessories, such as electronics, black/chrome, etc.
(5) Re-evaluate the Kurry driver & passenger pegs. Trash or keep? Keep-save some $$$$
(6) CB-Radio & Antenna? I will not purchase CB with more current technology for communication far & above CB Radio technology.
(7) Ram mounts reassessments for mounting for iPhone-GPS if I need additional besides the GW Navi unit-TBD/To Be Determined. ***Purchased the Carpuride W502 installed, and it works great. It mirrors the iPhone Carplay and works really great! (Update: I purchased the Carpuride 702pro seven-inch screen to replace the 502 five-inch screen. The 502 will serve as reserve if the 702pro fails or sell the Carpuride 502.)
I may be adding another Satellite Emergency device unless I use the Spot that I canceled service on, as I was not doing any long-distance traveling. I may sell it for an updated model before my Route 66 Adventure later in 2024, provided my health maintains me. Planning the Route is already formatted GPS on the Desktop with "MyRoutes GPS Mapping." I will update you in the near future! (I did not make the RTE 66 this year as I had hoped, so hopefully, the late spring of 2025 will work out for that adventure.)
ELECTRONICS-ACCESSORIES aka Farkles:
- I already purchased the “Electrical Connection Bluetooth” device (sold by CycleMax). It's installed and working!
- “EC Ground Loop Isolator” (purchased and produced by Electrical Connection and sold by CycleMax). It is not needed; no engine noise was noted will consider selling.
- Evaluate previous owners' LED lighting and keep or
trash? The evaluation of the LED lighting was impressive, and *I will keep the special effects LED lighting. (There is a push-button remote that is used to sequence between various colors and special effects; there is also a master two-way on/off push button with a RED waterproof cover over the push button located above the (- battery post) of the YUSA battery.) The YUSA BATTERY was R/R with a Battery Plus branded 12v Battery. - Add additional accessories, electronics, black/chrome, etc. Work in progress.
- Re-evaluate the Kurry driver & passenger pegs.
Trashor keep? So far, I will keep these to R/R cost not worth it. - CB-Radio & Antenna? I am not adding a CB with current technology on communication headsets, aka Mesh.
- Ram mounts: I installed the manufacturer's Ram-type mounts for the “Carpuride 7” Apple Car Play and the Ram Mount for the installed Garmin XT onto the MASTAD Base Shield.
- “MUTH MIRRORS” Installed Blue Tint Mirrors with Amber-sequence Chevron turn signals; PayPal paid $267.31 USD. To: shop.muthco.com Details 1x Honda Gold Wing GL 1800 $249.00 USD1x Shipping fee $18.31 USD Subtotal $267.31 USD Tax $0.00 USD Shipping is $18.31 USD, UPS Insurance is $0.00 USD, and Handling is $0.00 USD Total: $267.31 USD Paid with PayPal: Pay in 4 $66.83 USD City County Employees Credit Union ••••3756 paid today Shipped to: Alexander Herring, 1742 Indiana Avenue, Palm Harbor, FL 34683 Purchase details: Receipt Number: 5M817787L06048837 continued….
Merchant details: shop.muthco.com
August 2nd, 2023, previously ordered & then installed the “MUTH MIRRORS” Blue tint with Amber Chevron turn indicators. They do bring extra safety for drivers to the rear, knowing my intentions when turning in front of them. I may go back to adjust the wiring, as the Kurry “Y” splitter and the MUTH wiring made for a tight fit in the small compartment below the front cowl area beyond the mirrors. **MUTH MIRRORS carry a *three-year or 36,000-mile warranty against defects of the “LEDs”! Effective until July 27th, 2026!
November 30th, 2023
I installed the Show Chrome “Tridium DRL-Fog-Turn Signals.” I did have an electrical connection issue on the Fog lights due to defective (BLUE Connectors at the Fog lights connecting points). I learned that it is a defective issue, as noted by some reviews from previous customers. Initially, I tried using wiring tape to hold the two connection points together to complete the circuit (Failed!)
I have attempted to get a response from Wingstuff customer service concerning having failed components replaced [wire lead from turn signals to Fog-running lights & defective Fog-DLR Light Switch. I have not received any response from Wingstuff after two emails on their website. I also mailed a letter via USPS. I will post on the Wingstuff website on
GL1800RIDERS about this dilemma of no response from Wingstuff!
***I found a solution by using small zip ties to hold the two male/female connections together to complete the circuit. I then sealed it with wiring tape. It was after several tests of the operation of the Fog lights that I secured the wiring leading down from the “Turn Signals” connections and ran the Fog lights leads down in the front fairing cowl to the Fog lights located in the lower cowl. Before closing up everything, I again checked the operation of the Fog-DRL-Turn signals, and all worked!
*** I installed the power provided by the PDM60 Isolator in the left front pocket (Show Chrome-USB Dual Charger 2.5v X2 charging ports)!
*** I installed another Dual USB Charger/Battery Voltage monitor into the rear Tour Trunk powered via the PDM60 Isolator.
*** The next installation will be the Show Chrome “Left side Accessory USB Power Switch.” (It's installed and working!)
ADD any additional accessories below:
(9) MADSTAD Windshield purchased October 23rd, 2023
Toni or Blair 0830-1630 for pick up & payment for a 14” MADSTAD windshield.
On October 27th, 2023, I installed the 14” MADSTAD, which was too high in height at the lowest position. I called and spoke with Blair and explained the issue, and he said they would exchange it, which is not a problem.
November 1st, 2023, I drove back to MADSTAD to return the 14” shield for the 12” that had already been made for me. Upon comparing the new shield and placing it next to the 14”, the new shield was actually another 14” shield! Blair apologized for the error. He said he would get the 12” sent to me the following day, November 2, 2023, via UPS. I received the UPS tracking number, and the new 12” shield was delivered to me on November 3rd, 2023! It was the correct size! The fit was spot on, and I’m looking forward to seeing if all the hype is true about MADSTAD!
(10) I installed the 12” MADSTAD on November 4th, 2023, without incident, and I can now easily see above the windshield!
I will take it out and note the various angles to provide my comfort zone on the Highway at speed. To be continued
**Test rides on local roads and adjustments: I have not had any long rides at higher speeds for any length of time (all urban roads). But right now, from 30mph up to 60-70 mph, I have just smooth airflow in the rider and no buffeting of the helmet! Happy so far. The position of the air wings also changes the various airflows, which help regulate or fine-tune the airflow on and around the rider.
(11) On November 5, 2023, the Carpuride W502 Apple Car Play was ordered and is awaiting delivery for installation: Carpuride W502 Wireless Portable Dual Bluetooth Waterproof IP67 Motorcycle Stereo. This will enable Apple Car Play functions on the 2017 GL1832 via headphones or the onboard Electrical connection Bluetooth to allow feedback through the bike speakers! (An Update and review will follow installation.) (See 11 & 15 below for additional information.)
(12) 11/5/2023 I purchased Carpuride W502 via their website. This unit allows you to have CarPlay on the 2017 GL1832 while your phone is stored away from the elements! (This allows the iPhone CarPlay to be mirrored onto the Carpuride screen! Great! Apple CarPlay is now on the 2017 GL1832! Sweet! (I will update and review it after receiving and installing it on the GL1832.) R/R with the Carpuride 702pro 7” screen.
(13) The UTOPIA Backrest was ordered and installed from November 14 to 2023, and I’m looking forward to having lower midback support! I had one on the 2012 GL1832 and loved it! (I will update the review once I have some miles with Utopia!) LOVE IT!!!
(14) Honda 2012-2017 Service Manual with Electronic Trouble Shooting Manual Attached.
Delivered: via FedEx on August 6, 2023
**See (12) above Screen Shots of the Carlinkit Dongle: below pages.
(15) Apple Car Play Carpuride W502 installed 11/21/2023. I wired the W503 into the left cubby compartment area with an open existing hot (+) lead via wiretap and grounded (-) on the same lead. The W503 has an in-line 3amp fuse, so I did not need to run wiring down to the battery or to the PDM60 Isolator.
A Bluetooth connection was established with the iPhone, and I customized the ACP=Apple Car Playlist to my preferences. The GPS did not coordinate with the active iPhone Google Maps or Apple maps relating to E-W-S-N. I will update once I can do an actual test ride to see if the coordination of the location mode of travel displays the same as the iPhone mapping source. (I am still trying to figure out if I can tie the W503 into the GW speakers, yet it appears it is designed to connect via BT to the Helmet (according to the instruction material enclosed), which I have not attempted to test yet.
I will update you soon once I get the trial ride of the W503. The purchase was to keep the iPhone out of the weather, particularly the summer sun, which causes heat-related issues by reducing the screen brightness and, at times, disabling the iPhone to protect itself from heat damage.
I now have the option of storing the iPhone on my person, the left front cubby unsecured, the center lockable storage compartment, and the rear Tour Trunk, which I wired with a 3.5 & 2.5 USB charger/voltmeter, which was installed on 11/21/2023. (It is wired into the " PDM60 Power Distribution Module. ") **I can get Audio via the GW speakers once I BT the Carpuride W502 to the Electrical Connection! Good News!
Update**11-28-2023 I tried out the built-in EQ “Rock Mode,” and it sounds way better than the 2018 GW! Hearing the sound from the 2017 GW knocked my socks off! Love this CarpuRide W502!!! SEE BELOW for the purchase of the Carpuride 702pro installed to replace the W502.
(16) November 25, 2023: I installed the Show Chrome Tridium DRL-Fog-Turn Signal kit. The installation was lengthy, about 7 hours, taking my time and requiring me to readapt the disassembly of the plastic for some 5 years since I did on my 2012 GL1832. The Cruise Man DIY video was a great reference. Another issue was fishing the wire leads from the “Turn Signals on R & L” down within tight crevices from the mirrors down to the area of the FOG light connections. ☹!
I took all the front cowling off the front, the windshield, and its components to find an easier access point. I used the 3’ zip tie on the respective R & L mirrors to fish the Fog Lights cables and connect to both Fog lights! 😉
The connections (Blue) were not making the clasp lock as they should. I finally got the R side to lock, but the L never did (I will tape the Blue Connectors @ the Fog lights so they don’t disconnect!) I reconnected the (-) on the battery to test the connections and functions of the fog lights. All was working as they should (DRL-Amber Turn signals R & L)-Retina fryers Fog lights! I used the “Jumper” so the Fog lights will remain “ON” even when the “Bright lights function is active on the GW.” I will complete getting everything buttoned up tomorrow!
Problem with the Tridium fog light installation see the following;
Thanks for the reply! I am about to have my Tridium Fog-DRL-Turn signal kit finished up. It appears Show Chrome has already installed the "resistors" on the latest version of their Tridium Fog light kits. As new to me, 2017 GW has all incandescent lamps. I am not experiencing any issues with all functions of the Fog lights LEDs and the incandescent lamps. Yippy!
What was a pain in the Kester was intermittent LEDs working when they desired. I had to go back & forth to figure out the problem.
It turns out that the connectors from the main wiring from the mirrors down to the fog lights were the problem. The connectors on each of the plugs in the fog light were defective. I could never get the male & female clips to lock onto each other. It appears that they were just a smidge too long to allow a flush fit of the opposing connections.
Initially, I tried taping them with wiring tape in hopes it was enough to hold them together, but that didn't work! So, I decided to trim a small amount of the end of each connector so that it would allow a secure contact and allow the lock to secure the connection. That did the trick or so I thought but being that the plastic lock on the tab was so thin and flimsy, it was easy to separate them, the result was lights that worked when they wanted to!
**Update January 6, 2024: the main fog lights will not stay on; the only way they would activate is if I pressed very firmly on the Fog Light switch! The running and turn signal lights worked properly. I ordered a replacement “Fog Light Switch” from SoCal in hopes this will correct the issue with the crappy Show Chrome fog light switch! I will update once I R/R the Show Chrome fog light switch. Paying the kind of money for the Show Chrome lights “Tridium” and having to replace a Switch is a bummer! I will contact Show Chrome and ask for a replacement switch. If they want me to send the defective one, I will have it available because I will already have R/R the Show Chrome with the SoCal switch! Update to follow!
My Fix
So, I used a zip tie to wrap around the vertical axis of both the right and left connectors to hold them together. This appears to have solved the issue. I sure don't want to deal with a loose connection issue and disassemble it to deal with this again! If I have a reoccurring issue, I will cut the wires and soldier them together.
If I hear anyone having this issue on the forum with the Tridium fog lights with intermittent LED, I pass my fix on to them. I have a sneaking suspicion I will not be the only one who purchased the Black Friday sale on the Tridiums that got the bad batch of connectors on the fog light connecting points. I have way too many hours wasted getting the Fog lights operational, running down the issue, and fixing it. Oh well, I am happy with the outcome,, and these are some great Fog-DRL-Turn signals once I got them working correctly! Buttoned the GW up & no issues with the fog lights! 11-28-2023
[[UPDATE]] I installed the Socal Fog-DRL switch.
January 10th, 2024, I installed the Socal Fog Light switch to replace the Show Chrome Fog-DLR switch. It was defective as you had to press and hold the switch down for the DLR to activate; otherwise, the DLR would cut off when you released the switch. The Socal switch worked, but I had to use a wire tie to keep the connector between the switch and the power lead from the left cubby pocket wiring. At this moment, the Fog-DRL is working normally! 😊
**Show the Chrome 12v USB accessory for the left cubby pocket-storage area. It is currently being shipped, and I will update you after installation.
Update RE: Show Chrome 12v USB Accessory Charger 11-28-2023 was delivered. After looking over the packaging, I noticed that these were for the 2018 and up GWs. But they will fit into the 2017 Cuddy left side without issue. I drilled the 1-1/4” hole that was factory molded for the cutout to accept 12v accessory.
I installed the charger but have not wired it into the electrical system yet. I will have to route the power leads to the PDM60 later. I tied up the buttoning of the GW backup after the installation of the Tridium fog lights!
(17) Knob Key Project Order Number: 925807081-LOWES Clwtr
I ordered 2-Key Blanks “Axxess 27R B Cassettes +” Lowes 11-28-2023. I will make two Knob keys for Fuel Door & Glove Box.
I also ordered 2- Knobs of Black Rubber “Honda 35601-MCA-A8”1 from Parts-Zilla for making the Knob-Keys. (Update on completion of the installation)
In-Store Pick-Up Lowes Clearwater Store.
The above keys were cut down for the Honda Black radio knobs, and a small slot was cut off from each knob so the keys could be inserted and glued! I used the JB Weld plastic epoxy. It worked very well and provided a solid medium for attaching the keys to the radio knobs, which will be used on the Fuel access door and the Center cubby. This will allow me not to have to remove the ignition key to open the fuel and center cuddy when I need to have access to them. When leaving the GW, I can remove the two Radio knobs and secure them in the center cubby or the rear tour trunk.
HONDA CUSTOMER SERVICE AKA “MAW HONDA”
If YOUR problem still has not been resolved to YOUR satisfaction, please write Motorcycle Customer Service Department, American Honda Motor Co., Inc., P.O. Box 2200, Torrance, CA 90509-2200, or YOU may call Motorcycle Customer Service at (866) 784-1870.
(18) Honda Rear Spoiler OEM Pearl White installed October 13th, 2024, purchased from Cycle Max. The following additional accessories were installed with the rear Spoiler:
- Pathfinder SoCal Running Lights (rear) Sequential Turn Signals-Brake light Rapid Flash-Four Way function LEDs.
The new “Carpuride 702pro” was mounted in the center of the Madstad mounting base shield and secured with security mounting bolts and security Ram-type mounts requiring a Security Key to remove/reinstall them. The large real estate of the screen was a nice improvement for these old eyes! Once I figured out how to use Bluetooth and sync the iPhone, it worked flawlessly. Once I turn the key on, it initiates start-up, and “Apple Car Play” is up and running. I have hundreds of songs stored with various Genres of Artists at my fingertips on the “Apple Music App”.
(20) November 28th – 30th, 2024, Upgraded the OEM H3 Lo Beam Headlight Bulbs to “Pathfinder SoCal” LEDs." I purchased SoCal from the Pathfinder-SoCal web store. The installation was rated a (3) out of (5) scale of difficulty due to the tight areas which you must work on the front interior fairing area on the left & right sides of the fairing.
I was so impressed with the bright white image the LEDs provided compared to the OEM H3 Halogen bulbs' (brown/yellow) appearance. In fact, I liked them so much that I decided to purchase a second set of SoCal LEDs to replace the OEM Hi-Beam H3 Halogen with LEDs! These were purchased from Moto Tour (Pinellas Park-FL) as Pathfinder SoCal did not have any available. The installation is rated a (5) of (5) of difficulty.
This was due to the removal of the pockets Right and left, and the upper high beam mounting locations were very tight and cramped in the upward recesses of the fairing above the Lo beams! The ballast was secured in the small open areas on the right and left pockets of the interior fairing plastics.
*Despite the difficulty of this installation, it was again well worth the safety of nice crisp white bright headlights of Hi & Lo beams! The low points of this installation of the Hi beam LEDs, as noted, (1) were removing the top right and left shelter pockets, (2) the foot warmer controller adjuster component, the Plastic around the ignition key, and dislodging the left plastic panel of the inner fairing to gain access from the front section of the wheel area, rearranging the electrical wiring within those spaces.
It’s no wonder “Pathfinder SoCal” recommends that a professional technician install the Hi-Beam LEDs. But if you are mechanically inclined and have patience, you can handle this installation. Ask me how I know. 😊
(21) Gold Strike Cup Holder (rider) see bulleted additional accessories added:
- USB Charger with Voltage meter (Trunk)
- Kuryakyn Rear Saddle Bag Strip Red-LEDs (running lights)
- Kuryakyn Rear Fender Tip Red-LEDs
- Show Chrome Turn Down Exhaust Tips
- Utopia Back Rest (Rider)
- Ram Phone Mount (Rider)
- Baker Wind-Wings (Lower side R & L Fairings)
- Baker Wind Wings (Under R & L Mirrors)
- Muth Mirrors/Blue Tint (Amber Chevron Turn indicators)
- Front Brake Black Caliper Brake Covers (eBay) added white LEDs in the Ring.
- Madstad Windshields 12” Smoke and 14” Smoke were sent but were not the 12” Madstad I ordered. Madstad then sent the correct size, ordered a 12” Smoke, and advised me to keep the 14” smoke shield; no return was needed. I purchased Madstad from their Brooksville, FL, business/production location. Fantastic shield!
- Turns Signal Lens Covers-Smoked: Installed eBay/aka Flea Bay (DRL-white/Turn signals amber), which replaced the Cycle Max DRLs/Turn Amber LEDs due to better clarity color presentation. eBay was cheaper, too, and performed better.
- Fanttik Air compressor purchased the Clip On “Air Chuck,” which is easier to attach to the Valve stems than the screw on “Fanttik Air Chuck.”
- “Show Chrome Switch Block Illuminated LEDs (3) control switches.” The Brake reservoir mount has yet to be installed.
- FOBO TPMS (a great add-on that works as described but has great liability so far!)
- Big Bike Parts/WingStuff purchases a Black Stainless Steel “Belly Pan.” This item will provide some peace of mind by protecting the underside of the engine (oil filter, antifreeze Reservoir, engine case). Installed 12-5-2024
- Trunk Handle with Lamp/LEDs (Black) eBay aka Flea Bay Installed 12-10-2024; it came with no instructions, just the Hardware & the Metal Handle (appears to be solid quality); time will tell the real deal.) Yes, that is common with eBay purchases for most parts for the GWs. The M5 Screws with 3mm Allan head were way too long for the application (M5 was about 1 ½” long, which I cut down and ground to 3/8” or ½” don’t recall at this writing. Nonetheless, they worked just fine with securing the Handle to the trunk. I will have to update with the complete installation and electrical wiring that will need to be spliced into the Honda OEM wiring for running & brake lights. (*Maybe no brake lights are yet to be determined.)
- FARKLE: I purchased the LSC4X ADVANT Modular Helmet (Pearl White) from Amazon. I also bought and installed the Cardo X4 BT communicator. What was a great selling point is that LSC throws in with the helmet sell are the following items: (1) Dark Smoke shield, (2) Pinlock anti-fog shield, (3) LSC Advant backpack, (4) LSC Advant helmet bag. This Helmet will be used primarily on the Pearl White 2017 GoldWing. I washed the helmet with Dawn dishwashing soap and rinsed it with a damp microfiber towel. Adams ceramic graphene solution made an already stellar White Pearl paint POP even more so! I have yet to BT pair it to my iPhone and download any software upgrades if any are available. Also, I plan on incorporating it with the Carpuride 702 Pro in the Apple Carplay application. The Large seems a little tight around the temples; I hope it will break in to allow a comfortable fit. *I will update you once I get it paired with the Carpuride 702 Pro and the CSC Encore to take advantage of the 40 mm JBL Speakers. You know it's all about the sound.
